Power Plant

By -

TTP
Cessna 172
Cat.B1
L-3
ATA71
Power Plant
Cat.B2
L-1
Textron Lycoming IO-360-L2A engine is direct drive, four cylinder, fuel injected, horizontally opposed, and air cooled. The cylinders, numbered from front to rear, are staggered to have individual throws on the crankshaft for each connecting rod. The right front cylinder is number 1 and cylinders on the right side of the engine are identified by odd numbers 1 and 3. The left front cylinder is number 2 and the cylinders on the left side are identified as 2 and 4.

 IO-360-L2A Technical Description
172R Rated Horsepower at 2400 RPM 160
172S* Rated Horsepower at 2700 RPM 180
Number of Cylinders 4 
Horizontally Opposed
Displacement 361.0 Cubic Inches
Bore 5.125
Stroke 4.375
Compression Ratio 8.5:1
Firing Order 1-3-2-4
Magnetos:     Right  Slick 4371 (25°BTDC)
                        Left    Slick 4371 (25°BTDC)
Spark Plugs 18MM
Torque: 420 In lbs
Valve Rocker Clearance (hydraulic tappets collapsed)
0.028 to 0.080 inch
Fuel Injector RSA-5AD1
Tachometer Mechanical Drive
Oil Capacity 8.0 Quarts
Oil Pressure.      Min Idling 20 PSI
                             Normal 50 to 90 PSI
                             Maximum 115 PSI
Oil Temperature Normal 100°F to 245°F
Maximum 245°F
Dry Weight - without alternator or vacuum pumps 278
711001 Cowling - Inspect for cracks, dents, other damage and security of fasteners.
A 05-12-01 120
712001 Engine Shock Mounts, Engine Mount Structure, and Ground Straps - Check condition, security, and alignment.
712003 Inspect tubular engine mount.
716001 Alternate Induction Air System - Check for
obstructions, operation, and security.
A 05-12-01 120
716002 Induction System - Check security of
clamps, tubes, and ducting. Inspect for evidence
of leakage.
A 05-12-01 120
Revised
Aug 1/00
716003 Induction Airbox, Valves, Doors, and Controls - Remove air filter and inspect hinges,
doors, seals, and attaching parts for wear and security. Check operation.A 05-12-01 120
716004 Induction Air Filter - Remove and clean. Inspect for damage and service.

Comments

Post a Comment

Popular posts from this blog

VACUUM SYSTEM

By -
TTP B1-L3 ATA37 Cessna 172 B2-L2   V acuum system has a filter, vacuum gage, vacuum instruments, regulator valve, vacuum manifold,  low vacuum annunciator switches, engine-driven vacuum pumps and related plumbing.   With   Garmin G1000, the source of vacuum air is in the cabin and is pulled through the  system by the engine-driven vacuum pumps. This air goes through the gyro filter at the cabin inlet source  before it goes through the vacuum gage and gyro instruments. The vacuum is controlled by the regulator  valve. The regulator valve is on the aft side of the firewall. The vacuum air is then pulled through the  vacuum manifold and past the low vacuum annunciator switches and then into the vacuum pumps. Without Garmin G1000, vacuum pressure is measured by the low vacuum annunciator   switches in the engine compartment. The vacuum gage in the instrument panel shows the vacuum  pressure. Vacuum gag e gives a direct indication of the
Read more

LEVELING

By -
TTP B1-L1 ATA08 Cessna 172 B2-L1             PTP Cessna 172 B1 LOC SGH B2 LOC SGH Required tools, equipment and materials-. Leveling Points Lateral Leveling. (1) Find two points that are the same on each upper door sill of the left and right cabin doors. (2) Put a level in position across these points. NOTE: Out-of-level tolerance for wing tips is three inches total. (3) Make a note of the airplane's lateral position. (4) If applicable, put jacks in position at the wings and tail jacking points. (a) Adjust the wing jacks as required to get the necessary lateral position. Longitudinal Leveling. (1) Find the two screws on the left side of the airplane tailcone that are in line with water line zero. (2) Remove the screws. (3) Install studs or long screws of applicable length (approximately two inches long). (4) Put the level in position on the studs
Read more

FAA AD 2015-19-07 Lycoming Fuel Injected Reciprocating Engines

By -
           (1) Initial Inspecton _, inspect the fuel injector fuel lines and clamps between the fuel manifold and the fuel injector nozzles. Use MSB No. 342G,  to perform the inspection. Replace any fuel injector fuel line or clamp that fails the inspection required by the Fuel Line Inspection and Installation Checklist in MSB No. 342G.          (2) Re-inspect after any maintenance is done on the engine where any clamp on a fuel injector fuel line was disconnected, moved, or loosened, and within every 110 hours TIS and after each engine overhaul. 
Read more