AMSAFE working SIL-25-01

By -


TTP
B1-L1
ATA25
Cessna 172
B2-L1


TITLE EQUIPMENT/FURNISHINGS -AMSAFE AIRPLANE FLIGHT MANUAL SUPPLEMENT
EFECTIVITY  : MODEL 172R/172S/182/206

SERIAL NUMBERS 172R   - 17281588 thru 17281615  Watch Video for AMSAFE working
                                                                        

  This service letter provides instructions to make sure that the AmSafe Supplement is attached to the airplane's Pilot's Operating Handbook and FAA Approved Airplane Flight Manual.
       
ACCOMPLISHMENT INSTRUCTIONS

 1. Look at the Pilot's Operating Handbook (POH) and see if there is an E508810 Revision D  Flight Manual Supplement to Pilot's Operating Handbook and FAA Approved Airplane Flight
Manual for Cessna Aircraft Models: 172R, 172S

 A. If an E508810 AmSafe Supplement is attached to the airplane's POH, no further action is required.
B. If there is no E508810 AmSafe Supplement attached to the airplane's POH, attach the copy that is included with this service letter.
PTP
Cessna
172
B1
LOC
FOT
SGH
R/I

B2
LOC
FOT
SGH
R/I

Comments

Post a Comment

Popular posts from this blog

VACUUM SYSTEM

By -
TTP B1-L3 ATA37 Cessna 172 B2-L2   V acuum system has a filter, vacuum gage, vacuum instruments, regulator valve, vacuum manifold,  low vacuum annunciator switches, engine-driven vacuum pumps and related plumbing.   With   Garmin G1000, the source of vacuum air is in the cabin and is pulled through the  system by the engine-driven vacuum pumps. This air goes through the gyro filter at the cabin inlet source  before it goes through the vacuum gage and gyro instruments. The vacuum is controlled by the regulator  valve. The regulator valve is on the aft side of the firewall. The vacuum air is then pulled through the  vacuum manifold and past the low vacuum annunciator switches and then into the vacuum pumps. Without Garmin G1000, vacuum pressure is measured by the low vacuum annunciator   switches in the engine compartment. The vacuum gage in the instrument panel shows the vacuum  pres...
Read more

LEVELING

By -
TTP B1-L1 ATA08 Cessna 172 B2-L1             PTP Cessna 172 B1 LOC SGH B2 LOC SGH Required tools, equipment and materials-. Leveling Points Lateral Leveling. (1) Find two points that are the same on each upper door sill of the left and right cabin doors. (2) Put a level in position across these points. NOTE: Out-of-level tolerance for wing tips is three inches total. (3) Make a note of the airplane's lateral position. (4) If applicable, put jacks in position at the wings and tail jacking points. (a) Adjust the wing jacks as required to get the necessary lateral position. Longitudinal Leveling. (1) Find the two screws on the left side of the airplane tailcone that are in line with water line zero. (2) Remove the screws. (3) Install studs or long screws of applicable length (approximately two inches long). (4) Put the level...
Read more

FAA AD 2015-19-07 Lycoming Fuel Injected Reciprocating Engines

By -
           (1) Initial Inspecton _, inspect the fuel injector fuel lines and clamps between the fuel manifold and the fuel injector nozzles. Use MSB No. 342G,  to perform the inspection. Replace any fuel injector fuel line or clamp that fails the inspection required by the Fuel Line Inspection and Installation Checklist in MSB No. 342G.          (2) Re-inspect after any maintenance is done on the engine where any clamp on a fuel injector fuel line was disconnected, moved, or loosened, and within every 110 hours TIS and after each engine overhaul. 
Read more