Cessna 172R

720000 Fuel line (Stainless steel tube assembly)  and support clamp inspection and installation.  Refer to Lycoming Service Bulletin Number 342E or later version.  V 05-12-23 120 722001 Engine - Inspect for evidence of oil and fuel  leaks. Wash engine and check for security  of accessories.  A 05-12-01 120 722002 Crankcase, Oil Sump, and Accessory Section  - Inspect for cracks and evidence of oil leakage. Check bolts and nuts for looseness  and retorque as necessary. Check crankcase breather lines for obstructions,  security, and general condition. B 05-12-02 120 722003 Hoses, Metal Lines, and Fittings - Inspect  for signs of oil and fuel leaks. Check for abrasions, chafing, security, proper routing  and support and for evidence of deterioration 723001 Engine Cylinders, Rocker Box Covers, and  Pushrod Housings - Check for fin damage,  cracks, oil leakage, security of attachment,  and general condition.  B 05-12-02 120 723002 Engine Metal Lines, Hoses, Clamps, and  Fit

212001 Ventilation System - Inspect clamps,  hoses, and valves for condition and security. 212002 Remote Avionics Cooling Fan -  Op Check 214001 Cold and Hot Air Hoses - Check condition,  routing, and security.  05-12-02 Z120

Practical training is a structured training event which consolidates the knowledge gained during the theoretical phase of type training and as such, may be performed after or integrated within the theory training. However, it must not be performed before theoretical training. Practical training should: Address the different parts of the aircraft which are representative of the structure, the systems/components installed and the cabin. Include the use of technical manuals, maintenance procedures and the operational interfaces with the aircraft (e.g. FMC, electronic flight bag, etc). Include common maintenance and ground handling activities. Cover both type specific and generic safety elements of the aircraft’s maintenance. Develop the student’s competence in performing safe maintenance, prior to the practical assessment. Purpose of Practical training is not to include all the maintenance tasks associated with a particular type, but a representative sample of them that will a

A portable, hand operated fire extinguisher is mounted on the floor between the pilot and copilot seats for use in the event of a fire. The extinguishing agent is Halon 1211 and may be used on solid combustible, electrical or liquid fires. Servicing of the extinguisher can be handled by most fire equipment dealers. The fire extinguisher is mounted within a quick release, clamp type bracket assembly. 262001 Portable Hand Fire Extinguisher - Inspect  for proper operating pressure, condition,              security of installation, and servicing date.  B 05-12-01 230 262002 Cockpit Mounted Halon Type Fire Extinguisher  - Weigh bottle. Bottle must be                         reserviced  by qualified individual if more than  2 ounces is lost. 262003 Cockpit Mounted Halon Type Fire Extinguishers  - Perform hydrostatic test. The                      hydrostatic  test shall be at twelve-year intervals  based on initial servicing or date of               last  hydrostatic test.

A single axis autopilot with heading hold is on airplanes with IFR. Heading hold is used with directional gyro input and can have VOR, GPS or Localizer input as required. Dual-axis autopilot is available. The dual-axis system gives both vertical speed and altitude hold selection. The autopilot on this aircraft uses a pitch servo, a pitch trim servo and a roll servo. GFC-700 is a dual-axis autopilot with heading, altitude, and vertical speed hold 221003 Autopilot Servo Actuators. Inspect for evidence  of corrosion and or buildup of dirt or other particulate matter which may interfere  with servo operation.  O 05-12-16 Z610

Level 1 A brief overview of the airframe, systems and powerplants as outlined in the Systems Description Section of the Aircraft Maintenance Manual / Instructions for Continued Airworthiness. Course objectives: Upon completion of the course, the student will be able to: a) provide a simple description of the whole subject, using common words and examples, using typical terms and identify safety precautions related to the airframe, its systems and powerplant; b) identify aircraft manuals, maintenance practices important to the airframe, its systems and powerplant; c) define the general layout of the aircraft's major systems; d) define the general layout and characteristics of the powerplant; e) identify special tooling and test equipment used with the aircraft Level 2 Basic system overview of controls, indicators, principal components including their location and purpose, servicing and minor troubleshooting. General knowledge of the theoretical and practical aspect